ACCURATE AND DEPENDABLE TORQUE

Since torque is transmitted via a hysteresis field, there is minimal difference between the static and the dynamic torque. These units are unaffected by friction and wear, therefore torque is substantially more accurate and repeatable than friction tensioners.

CONSTANT TORQUE (ADJUSTABLE)

Units can deliver set torque regardless of speed range. Each unit's torque settings may be manually adjusted over a wide range providing great flexibility.

STABLE TORQUE

A consistent torque is maintained regardless of allowable slip speed due to the hysteresis principle.

SIMPLE INSTALLATION

Units are provided bearing mounted and pre-assembled.

LONG LIFE

There is virtually no wear because permanent magnets and hysteresis discs transmit the torque by magnetic flux without physical contact.

NO CONTAMINATION

Units are sealed to protect against contamination from equipment. There are also no wear particles from operation to contaminate equipment.

NO ELECTRICAL POWER NEEDED

The PHT series clutches and brakes operate on a permanent magnet priciple. External electrical connection is not required, therefore, units function independently from power fluctuation.

VERTICAL AND HORIZONTAL OPERATIONb>
Units can be mounted in any axis and can be run either clockwise or counter-clockwise without affecting performance.


Click display to add or subtract column categories

Click on column heading to sort table by category

Model
No.
Ogura
P/N
Static
Torque
(ft-lbs)
max
RPM
Bore
(inch)
Volts/
Watts
Keyway Wgt
(lbs)
PIC PDF DXF
PHT-70D 23622300 5.16 700 16mm 0/0 5x18.3mm 17.40 picture icon Download PDF DXF
PHT-30D 23621200 2.25 1000 16mm 0/0 5x18.3mm 7.93 picture icon Download PDF DXF
PHT-0.5S 25297100 0.041 1800 6mm shaft 0/0 D shaft 0.19 picture icon Download PDF DXF
PHT-1.2D 25295100 0.150 1800 6mm 0/0 Set screw 0.66 picture icon Download PDF DXF
PHT-2.5D 25297200 0.291 1800 6mm 0/0 Set screw 1.25 picture icon Download PDF DXF
PHT-5D 25297300 0.550 1800 8mm 0/0 3x9.4mm 1.85 picture icon Download PDF DXF
PHT-10D 25297400 1.08 1800 15mm 0/0 5x17.3mm 3.52 picture icon Download PDF DXF
PHT-0.02D 25384800 0.0025 3600 5mm shaft 0/0 D shaft 0.11 picture icon Download PDF DXF
PHT-0.05D 25388100 0.0052 3600 5mm shaft 0/0 D shaft 0.12 picture icon Download PDF DXF
PHT-0.5D 25386400 0.041 3600 8mm shaft 0/0 D shaft 0.32 picture icon Download PDF
PHT-0.05S 25297000 0.0052 10000 3mm shaft 0/0 D shaft 0.19 picture icon Download PDF DXF
PHT-0.02S 25293000 0.0025 10000 3mm shaft 0/0 D shaft 0.13 picture icon Download PDF DXF

Only maximum torque is listed above. Check pdf file for actual torque range.

© 2015 Ogura Industrial Corp. All rights reserved.
The contents of this website are protected under US copyright laws.
This site has been issued a certificate of registration by the United States copyright office, registration # TX 6-426-894

Ogura Industrial Corp. 100 Randolph Road • Somerset, New Jersey 08873
Phone: 732-271-7361 • Fax: 732-271-7580 • info@ogura-clutch.com


Home  |   About  |   What's New  |   Quick Selection Tool  |   Search  |   Careers  |   Contact